-
WHY IS A LOW JITTER FEATURE IMPORTANT IN ACTIVELY Q-SWITCHED DPSS LASERS?
May 13 , 2021
WHY IS A LOW JITTER FEATURE IMPORTANT IN ACTIVELY Q-SWITCHED DPSS LASERS? In actively Q-switched lasers, the user controls the pulsed laser output, so that no laser pulse emission occurs without providing a proper input signal, aka "the trigger". Due to the trigger signal propagation through the interface electronics, the Q-switch driver chain, and the laser resonator build-up time, a time delay (...
view more
-
Is laser engraving on ABS plastic harmful if you smell it?
May 13 , 2021
Is laser engraving on ABS plastic harmful if you smell it? Did you apply a data-driven approach to improve site structure? A confusing site architecture doesn‘t confuse Google, it impacts profits. Untangle it to see results! Of course no. Check the wikipedia below first: ABS is stable to decomposition under normal use and polymer processing conditions with exposure to carcinoge...
view more
-
What is the cheapest and best place to get plastic, laser engraved?
May 13 , 2021
What is the cheapest and best place to get plastic, laser engraved? The "right" answer to this question is going to depend on exactly what you need done. What you're describing is, for industrial manufacturers of things, still a relatively short run, and laser cutting/engraving is much like printing. The setup is the hard part, and the rest is largely about letting it run. Here are the sorts of qu...
view more
-
Nanosecond solid-state laser solves the marking problem of plastic control panel
May 14 , 2021
Nanosecond solid-state laser solves the marking problem of plastic control panel Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other c...
view more
-
Application of picosecond laser cutting machine in circuit board industry
May 14 , 2021
Application of picosecond laser cutting machine in circuit board industry The principle of the picosecond laser cutting machine is to focus the laser light emitted from the laser into a high-power density laser beam. When the laser beam irradiates the surface of the workpiece, the workpiece reaches the melting point or boiling point, and the high-pressure gas coaxial with the beam will melt...
view more
-
Application of UV laser in etching FPC circuit board
May 14 , 2021
Application of UV laser in etching FPC circuit board In recent years, the penetration rate of laser processing equipment has become higher and higher. Almost all industrial manufacturing fields have lasers. More and more industries are inseparable from laser manufacturing technology. This is due to the non-contact processing of laser processing methods. , High efficiency, low impact on materials, ...
view more
-
For laser marking on plastics, 3W5W UV laser can be selected
May 17 , 2021
For laser marking on plastics, 3W5W UV laser can be selected Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is a function of the wavelength. Therefo...
view more
-
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear
May 17 , 2021
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is ...
view more
-
Plastic panel UV laser lettering has little effect, no deformation or scorching
May 17 , 2021
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is ...
view more
-
Application of Picosecond Laser Cutting Machine in Ultra-thin Metal Foil
May 17 , 2021
Application of Picosecond Laser Cutting Machine in Ultra-thin Metal Foil In the field of ultra-thin metal materials, copper foil, stainless steel foil, titanium alloy foil, nickel alloy foil and other material processing tools, it is realized by die cutting or chemical etching. With the continuous improvement of demand, especially in 5G, Under the high standards of aerospace, satellit...
view more
-
Ultraviolet laser cutting machine is the most commonly used equipment
May 17 , 2021
Ultraviolet laser cutting machine is the most commonly used equipment in the field of micro-precision laser processing. It is mainly used for precision laser cutting, resistance adjustment, etching, scribing, drilling and other applications. It is commonly used in 3C electronics, medical, photovoltaic, automotive, aerospace And many other fields. Common cutting application materials include PCB, F...
view more
-
Why choose UV laser cutting machine for wafer cutting
May 17 , 2021
Why choose UV laser cutting machine for wafer cutting Most semiconductor materials have a good absorption of light in the ultraviolet band. Take the absorption of monocrystalline silicon in different wavelength bands as an example. When laser processing in the ultraviolet band is used to process semiconductor materials, due to the narrow focus spot of ultraviolet light, the photon energy is ...
view more
