10W-15W uv laser

Old customers buy 355nm UV laser again for glass inner engraving and cutting

RFH355nm UV laser has been developed for many years and has been loved by many customers. A customer from Malaysia recently purchased two RFH UV lasers for the inner engraving of glass crafts.

  • Laser Wavelength:

    354.7nm
  • Average Output Power :

    10W/12W/15W @40kHz
  • Pulse Width:

    <20ns @40kHz
  • Pulse Repetition Rate :

    10-200kHz
  • Spatial Mode:

    TEM00
  • Beam Quality (㎡) :

    <1.2
  • Beam Diameter:

    0.8±0.1mm Measured at window
  • Beam Full Divergence Angle :

    <2mrad
  • Beam Circularity:

    >90%
  • Pulse-To-Pulse Stability:

    <3% RMS/@30kHz
  • Average Power Stability :

    <5% RMS/8hr
  • Beam-Pointing Drift:

    <25μrad/℃
  • Polarization Ratio:

    >100:1
  • Polarization Orientation:

    Horizontal
  • Operating Temp. & RH:

    10℃ to 35℃ | <80%
  • Storage Temp. & RH:

    10℃ to 35℃ | <90 %
  • Electricity Requirement :

    100-240VAC |50/60Hz | Single phase
  • Power Consumption:

    <800W
  • Warranty :

    18months
  • Product Detail
  • Video

uv laser

Old customers buy 355nm UV laser again for glass inner engraving and cutting

 

engraving glass

 

 

When the light beam enters the glass, part of the light will be reflected on the surface, and most of the light will pass through the glass directly. The same is true for ultraviolet rays. When the ultraviolet laser emits ultraviolet laser light to the glass surface, it will be etched, so that the laser can be engraved inside the glass, so as to achieve the desired effect.

 

RFH 355nm UV laser has been developed for many years and has been loved by many customers. A customer from Malaysia recently purchased two RFH UV lasers for the inner engraving of glass crafts.

 

In the past, he bought UV lasers for cutting glass crafts and got quite good results. Although a UV laser can perform various processes such as marking, cutting, and internal engraving, Mr. Liang chose to trust RFH UV lasers again in the context of industrial expansion.

 

RFH UV laser has ultra-high energy density, usually higher energy density will cause glass cracks or even chipping, too low will result in the failure of reasonable internal engraving production, but the energy beam of UV laser is just right. The almost zero thermal effect makes the internal engraving of the RFH UV laser smooth, without breaking the glass or wasting raw materials.

 

In addition to cost reduction, the internal engraving process of RFH ultraviolet laser can control the minimum error of production at 0.02mm, and the incision is smooth and burr-free, which fully meets Mr. Liang's requirements. In addition, the unique Q-modulation technology can be connected to a variety of computers and programs, and the simple operation makes the control more convenient.

 

The RFH UV lasers that Mr. Liang purchased successively are all used in glass marking, drilling, engraving, cutting, etc., which have brought great help to the efficiency of his factory, and also gave RFH and customers the opportunity to grow together.

15watt high power uv laser etching,marking white on glass

 

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
K-6 Integrated UV Laser 4W-6W
K-6 Integrated UV Laser 4W-6W-8W
K-6 series UV DPSS laser, developed and produced by RFH, covers 4W/6W/8W in laser power with short pulse width (<20ns@30K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%). K-6 series laser is ideal for high-end ultra-precise processing as well as marking in mobile phone shell , package of cosmetics, food, medicine and other high polymer materials, PCB, LCD, glassware surface, metal’s cladding material, plastic keypad, electronic component, gift, communication device, construction material and other areas.
Download datasheet
K-6 Integrated UV Laser 4W-6W
Why RFH UV laser is often used in laser marking plastic button switch?
Why RFH UV laser is often used in laser marking plastic button switch
Why RFH UV laser is often used in laser marking plastic button switch? More and more manufacturers choose UV laser marking machine to create pattern and characters on the plastic button switch. The focal spot of UV laser is pretty small with little heat transfer to surrounding material, so UV laser is also called “cold light source”. Because of this feature, heat effect won’t occur. Thus, distorting or burning of materials is no longer an issue.    Professional UV laser manufacturer - Shenzhen RFH Laser Technology Co.,Ltd    With 13 years of experience, the S9 series nanosecond UV laser developed and produced by RFH can engrave clear characters on the keyboard and the mouse. These kinds of characters can not only help people identify different buttons in the dark but also last long, for there are slightly protruding part on the buttons. This improves the durability and practicability of the keyboard and the mouse.   
Why RFH UV laser is often used in laser marking plastic button switch?
UV laser
UV laser featuring cold processing for marking plastic button on keyboard
 UV laser featuring cold processing for marking plastic button on keyboard More and more manufacturers choose UV laser marking machine to create pattern and characters on the plastic button switch. The focal spot of UV laser is pretty small with little heat transfer to surrounding material, so UV laser is also called “cold light source”. Because of this feature, heat effect won’t occur. Thus, distorting or burning of materials is no longer an issue.    Professional UV laser manufacturer - Shenzhen RFH Laser Technology Co.,Ltd    With 13 years of experience, the S9 series nanosecond UV laser developed and produced by RFH can engrave clear characters on the keyboard and the mouse. These kinds of characters can not only help people identify different buttons in the dark but also last long, for there are slightly protruding part on the buttons. This improves the durability and practicability of the keyboard and the mouse.   
UV laser
355nm UV laser
How can 355nm UV lasers be used in industrial production?
How can 355nm UV lasers be used in industrial production?   In modern industrial production, laser is an indispensable part. As the requirements for processing accuracy become more and more detailed, lasers are deeply involved in industrial links such as marking and cutting.
355nm UV laser
Laser engraving glass
Laser engraving glass, green laser or UV laser, which is better
Laser engraving glass, green laser or UV laser, which is better   At present, green lasers are widely used in the production of marking and engraving beer glasses, so many manufacturers have accelerated the promotion of production lines, and in fact, RFH UV lasers can also mark on glass.
Laser engraving glass
cuts diamonds
RFH 3W 5W 10W UV laser cuts diamonds, smooth without bursting
RFH 3W 5W 10W UV laser  cuts diamonds, smooth without bursting   Diamonds are one of the most high-end luxury goods. They are not only bright and look very bright, but also are one of the hardest substances in the world and have a very high collection value.
cuts diamonds
Marking Plastics
RFH 355nm UV Laser Cold Light Source Marking Plastics, No Carbonization, No Burning
RFH 355nm UV Laser Cold Light Source Marking Plastics, No Carbonization, No Burning   In the surface marking of plastics, there are always problems such as material being scorched, but the research and development of RFH 355nm UV laser has completely solved this problem, allowing more small and medium-sized growth enterprises whose main business is plastic marking to survive and room for development.
Marking Plastics
marking plastic auto parts
UV nanosecond laser marking plastic auto parts, accompany you to travel safely
UV nanosecond laser marking plastic auto parts, accompany you to travel safely   The development of automobiles has greatly facilitated human life, and the research and development of new energy vehicles has combined greenness and convenience. Plastic auto parts occupy an important position in the development and installation of automobiles, but the complex shape and a large number of demands make the marking of characters more complicated, and the RFH UV nanosecond laser can solve this problem very well.
marking plastic auto parts
Get the latest offers Subscribe for our newsletter

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact