-
WHY IS A LOW JITTER FEATURE IMPORTANT IN ACTIVELY Q-SWITCHED DPSS LASERS?
May 13 , 2021
WHY IS A LOW JITTER FEATURE IMPORTANT IN ACTIVELY Q-SWITCHED DPSS LASERS? In actively Q-switched lasers, the user controls the pulsed laser output, so that no laser pulse emission occurs without providing a proper input signal, aka "the trigger". Due to the trigger signal propagation through the interface electronics, the Q-switch driver chain, and the laser resonator build-up time, a time delay (...
view more
-
What is the cheapest and best place to get plastic, laser engraved?
May 13 , 2021
What is the cheapest and best place to get plastic, laser engraved? The "right" answer to this question is going to depend on exactly what you need done. What you're describing is, for industrial manufacturers of things, still a relatively short run, and laser cutting/engraving is much like printing. The setup is the hard part, and the rest is largely about letting it run. Here are the sorts of qu...
view more
-
How do you laser-engrave a gradient on acrylic
May 13 , 2021
How do you laser-engrave a gradient on acrylic? Should I fill in lighter sections with a pattern (dots) or with a shallower solid fill? Steve Anderson, former Equipment Tech III Specialized Physics & Astronomy at Sonoma State University (1980-2019) Answered 3 years ago · Author has 900 answers and 171.1K answer views This is a tough question, depends on the image and the desired ...
view more
-
0.02mm high-precision UV laser is not easy to cause damage to 3C electronic components
May 14 , 2021
0.02mm high-precision UV laser is not easy to cause damage to 3C electronic components Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other co...
view more
-
Nanosecond solid-state laser solves the marking problem of plastic control panel
May 14 , 2021
Nanosecond solid-state laser solves the marking problem of plastic control panel Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other c...
view more
-
Application of UV laser cutting machine in high-end industry
May 14 , 2021
Application of UV laser cutting machine in high-end industry With the gradual maturity and stability of ultraviolet lasers, the laser processing industry has shifted from infrared lasers to ultraviolet lasers. At the same time, the application of ultraviolet lasers is becoming more and more popular, and laser applications are moving towards a broader field. Ultrav...
view more
-
For laser marking on plastics, 3W5W UV laser can be selected
May 17 , 2021
For laser marking on plastics, 3W5W UV laser can be selected Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is a function of the wavelength. Therefo...
view more
-
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear
May 17 , 2021
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is ...
view more
-
Plastic panel UV laser lettering has little effect, no deformation or scorching
May 17 , 2021
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is ...
view more
-
Application of Picosecond Laser Cutting Machine in Ultra-thin Metal Foil
May 17 , 2021
Application of Picosecond Laser Cutting Machine in Ultra-thin Metal Foil In the field of ultra-thin metal materials, copper foil, stainless steel foil, titanium alloy foil, nickel alloy foil and other material processing tools, it is realized by die cutting or chemical etching. With the continuous improvement of demand, especially in 5G, Under the high standards of aerospace, satellit...
view more
-
Ultraviolet laser cutting machine is the most commonly used equipment
May 17 , 2021
Ultraviolet laser cutting machine is the most commonly used equipment in the field of micro-precision laser processing. It is mainly used for precision laser cutting, resistance adjustment, etching, scribing, drilling and other applications. It is commonly used in 3C electronics, medical, photovoltaic, automotive, aerospace And many other fields. Common cutting application materials include PCB, F...
view more
-
Application of picosecond laser cutting machine on flexible screen
May 17 , 2021
Application of picosecond laser cutting machine on flexible screen The so-called flexible screen refers to a screen that can be bent and folded freely. As a brand-new field, flexible screens are faced with many problems in the processing process, and higher requirements are put forward on the processing technology. Compared with traditional brittle material processing, OLED display screens must be...
view more
