10W-15W uv laser

RFH 35W green laser is used for chip PCB cutting

RFH green laser has been favored by many manufacturers in recent years.

 

The RFH green light laser uses green light spots for non -contact cutting, which can help cut the chip with extremely small volumes for cutting, and can also scan and cut into cutting according to the shape of the need.

  • Laser Wavelength:

    532nm
  • Average Output Power :

    35W @50kHz
  • Pulse Width:

    <25ns @50kHz
  • Pulse Repetition Rate :

    10-200kHz
  • Spatial Mode:

    TEM00
  • Beam Quality (㎡) :

    <1.2
  • Beam Diameter:

    1.0±0.2mm Measured at window
  • Beam Full Divergence Angle :

    <1.2mrad
  • Beam Circularity:

    >90%
  • Pulse-To-Pulse Stability:

    <2% RMS/@30kHz
  • Average Power Stability :

    <3% RMS/8hr
  • Beam-Pointing Drift:

    <30μrad/℃
  • Polarization Ratio:

    >100:1
  • Polarization Orientation:

    Horizontal
  • Operating Temp. & RH:

    10℃ to 35℃ | <80%
  • Storage Temp. & RH:

    -20℃ to 65℃ | <90 %
  • Electricity Requirement :

    100-240VAC |50/60Hz | Single phase
  • Power Consumption:

    <800W
  • Warranty :

    18months
  • Product Detail
  • Video

uv laser

RFH 35W green light laser is used for chip PCB cutting


The chip occupies a very important position in the entire world economic market. The chip has a very wide application in electronic equipment and machine tools. The continuous rise in chip prices has also given us more reverie in the improvement of chip technology. Essence

 

RFH green laser has been favored by many manufacturers in recent years.

 

The RFH green laser uses green light spots for non -contact cutting, which can help cut the chip with extremely small volumes for cutting, and can also scan and cut into cutting according to the shape of the need.

 

The light spots emitted by RFH green light laser are relatively small, but the energy is not low. In fact, in the process of radiation spots, the laser beam of great energy will not hurt other positions, but it is complete when the thermal efficiency is zero. The ground retains other parts and reduces the scrap rate of materials.

 

In addition, the RFH green laser also has a very small accuracy, which is very suitable for cutting the chips in tiny electronic devices. The ability to run continuously for 24 hours brings battery life to production. Productivity.

 

 

The cutting of RFH green laser brings unlimited possibilities for chip production, and RFH continues to create new possibilities in this unlimited possibility to transport continuous technology and strength for the Chinese chip market.

 

Expert III 532 series green DPSS laser, developed and produced by RFH, covers 35w in laser power with short pulse width (<25ns@50K) ,superior beam quality (M²<1.2) and perfect laser spot quality (beam circularity >90%).It is perfect for glass marking,thin film etching and surface treatment for most of the metals and non-metal materials, such as removing the oxide layer from the metal surface

green laser

 

Expert III 532 series uv laser characteristics:   

1. 532nm output wavelength, 10 to 200 Hz repetition rate; laser power is 35w; Continuous tuning of repetition rate while maintaining constant pulse energy, superior beam pointing and energy stability make the Expert III 532 the first choice for micromachining, marking and thin film removal applications 

 

2. Exceptional beam quality (M²<1.2) ,absolutely assured in all repetition rates; relatively short pulse width <25ns@50K with little heat transfer to surrounding material; perfect beam spot quality(Beam Circularity>90%) 

Close to Gaussian smooth beam profile with low value M² < 1.2 and good focusability are beneficial for applications such as  

 

3. Unique Q-switching technology, adapts a variety of control requirements of laser applications;Online refreshment for harmonic coupling technology;Excellent long term power stability Rugged sealed cavity, Extremely compact size, Simple and robust 

 

4. Digital control technology for the driver,  RS232 control interface ensures easy control and integration with laser marking equipment 

 

5. This laser adopts one - style design with compact and reasonable structure, easy installation. 

Easy to transport and saves space due to compact and light design 

 

Water cooling,cost-effective and reliable end-pumping technology and amplifier-free DPSS design guarantee easy operation and alignment simple installation and low maintenance costs

 

6. Industrial production process control technology,provides quality stable products.

GREEN LASER

GREEN LASER

 

 RFH - The leading industrial solid-state laser manufacturer

 

For over 13 years with excellent long term stability and exceptional good beam quality

 

Production in dust-free plant & rigorous quality control system

From purchasing, pre-production quality check, assembling, finished product testing, warehouse-in inspection, pre-delivery testing to after-sales service, each step is under control to make sure product quality and consistency in both machine parameters and actual running parameters. This is what makes RFH laser lasts longer than its peers. 

RFH LASER

Top professional team, independent R&D in laser oriented power supply control system

 

There is a one-to-one correspondence between power supply and laser. The stability of power supply control system determines if the laser can maximize its performance during operation. RFH Laser has independent R&D in power supply technique which enables timely update and improvement of power supply control system module based on the laser’s need. 12-year experience in R&D and a top professional team make RFH laser a reliable and stable laser system.

green laser

Core components of oversea brands with guaranteed quality

Pumping, Q-switching and other core components adopt oversea brands. Work with top brand component suppliers of home and abroad. Each component is guaranteed with its quality from the beginning of materials purchasing. This is why users can trust RFH laser.  

35W green laser

 

UV laser+power supply+cooling system sold in a group

Being client-oriented, RFH offers proposal of selling the whole laser system in a group so that the laser system can maximize its performance while maintaining its stability. 

35W green laser

 

Full-digital display, supporting communication with computer, capable of laser’s remote control

Each laser developed and produced by RFH can always remain high quality in industrial and extreme conditions of scientific research. With stable beam quality, high efficiency, best cost performance and high reliability, RFH has earned good reputation in different industries at home and abroad. After 12-year development, RFH has become a reputed brand in nanosecond laser industry. 

uv laser | green laser | Ultraviolet lasers | uv dpss laser | nanosecond laser | UV laser source | Solid State Lasers

UV LASER

Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Related products
532 green laser is used to laser mark on ceramic knife
532 green laser is used to laser mark on ceramic knife
532 green laser is used to laser mark on ceramic knife Using RFH 532nm green laser to laser mark on ceramic knife enables the pattern on it to be very clear and doesn’t affect its normal cutting performance. This maximizes the brand quality and the delicacy of the ceramic knife.   Today, RFH is going to share the case of a ceramic knife supplier whose peer recommends RFH 10W 532nm green laser to him.    As we all know, marking on a ceramic knife adopts a laser marking technique. The whole marking process on the ceramic knife is so simple and generally takes a few seconds to finish. But this seemingly “simple” process needs to be supported by a well-established technique.And that is a laser system with exceptional laser beam quality and its accessories. An excellent laser is the basis of 99% yield of laser marking product and the solid-state green laser produced by RFH with 13-year experience is the perfect example.   
532 green laser is used to laser mark on ceramic knife
RFH green laser is recommended by a peer of a ceramic knife supplier
RFH green laser is recommended by a peer of a ceramic knife supplier
With brand strength, RFH green laser is recommended by a peer of a ceramic knife supplier Using RFH 532nm green laser to laser mark on ceramic knife enables the pattern on it to be very clear and doesn’t affect its normal cutting performance. This maximizes the brand quality and the delicacy of the ceramic knife.   Today, RFH is going to share the case of a ceramic knife supplier whose peer recommends RFH 10W 532nm green laser to him.    As we all know, marking on a ceramic knife adopts a laser marking technique. The whole marking process on the ceramic knife is so simple and generally takes a few seconds to finish. But this seemingly “simple” process needs to be supported by a well-established technique.And that is a laser system with exceptional laser beam quality and its accessories. An excellent laser is the basis of 99% yield of laser marking product and the solid-state green laser produced by RFH with 13-year experience is the perfect example.   
RFH green laser is recommended by a peer of a ceramic knife supplier
RFH 532nm green laser marking glass with ±0.02mm High precision
RFH 532nm green laser marking glass with ±0.02mm High precision
RFH 532nm green laser marking glass with ±0.02mm High precision 532nm green laser is a great accomplishment of RFH which has 13 years of R&D experience. It has perfect beam spot quality(Beam Circularity>90%) , relatively short pulse width <35ns@30K with little heat transfer to surrounding material and exceptional beam quality (M²<1.3) absolutely assured in all repetition rates. These features of 532nm green laser guarantee fast marking speed and delicate marking performance.  In addition, RFH 532nm green laser has independent R&D in power supply technique,which enables timely update and improvement of power supply control system module based on the laser’s need. The unique Q-switching technology makes it applicable to a variety of control requirements of laser applications. Online refreshment for harmonic coupling technology ensures its long life time. Therefore, RFH 532nm green laser is very ideal to be integrated into UV laser glass marking machine.
RFH 532nm green laser marking glass with ±0.02mm High precision
Two more green lasers are ordered by a Singapore glassware laser marker
Two more green lasers are ordered by a Singapore glassware laser marker
Two more green lasers are ordered by a Singapore glassware laser marker 532nm green laser is a great accomplishment of RFH which has 13 years of R&D experience. It has perfect beam spot quality(Beam Circularity>90%) , relatively short pulse width <35ns@30K with little heat transfer to surrounding material and exceptional beam quality (M²<1.3) absolutely assured in all repetition rates. These features of 532nm green laser guarantee fast marking speed and delicate marking performance.  In addition, RFH 532nm green laser has independent R&D in power supply technique,which enables timely update and improvement of power supply control system module based on the laser’s need. The unique Q-switching technology makes it applicable to a variety of control requirements of laser applications. Online refreshment for harmonic coupling technology ensures its long life time. Therefore, RFH 532nm green laser is very ideal to be integrated into UV laser glass marking machine.
Two more green lasers are ordered by a Singapore glassware laser marker
532nm green laser engraving glass of car
532nm green laser engraving glass of car
532nm green laser engraving glass of car Using RFH 532nm green laser to mark LOGO on automobile windscreen can make sure the logo to be accurate, high-definition and long-lasting after long time driving.   High precision of ±0.002mm, high stability and high cost performance are the core advantages of RFH green laser.   RFH green laser features 532nm laser wavelength. It is this small laser wavelength that decides the excellent beam quality and small focal spot of the green laser. Therefore, it can perfectly meet the needs of ultra-precise marking of automobile windscreen with the minimum character being 0.02mm.  
532nm green laser engraving glass of car
RFH 532nm green laser is used to mark Logo on windscreen of luxurious automobile
RFH 532nm green laser is used to mark Logo on windscreen of luxurious automobile
RFH 532nm green laser is used to mark Logo on windscreen of luxurious automobile Using RFH 532nm green laser to mark LOGO on automobile windscreen can make sure the logo to be accurate, high-definition and long-lasting after long time driving.   High precision of ±0.002mm, high stability and high cost performance are the core advantages of RFH green laser.   RFH green laser features 532nm laser wavelength. It is this small laser wavelength that decides the excellent beam quality and small focal spot of the green laser. Therefore, it can perfectly meet the needs of ultra-precise marking of automobile windscreen with the minimum character being 0.02mm.  
RFH 532nm green laser is used to mark Logo on windscreen of luxurious automobile
RFH 35W green laser marking-glass logo, So Easy
RFH 35W green laser marking-glass logo, So Easy
RFH 35W green laser marking-glass logo, So Easy   South Korean customer Fach produces glass wine cups. Before, the factory also used a brand of green laser, but there were always some wine cups with little defects which were overheated during processing, causing the wine cups to scorch or even deform.   Introduced by a friend, Fach has learned that the RFH Expert III 532 green laser is very effective for marking glass. So he has ordered one from us and tested the effect. After using our laser, Fach said that the heat affected area of the laser during processing is very small, which is very suitable for their laser application, and there will be no scorching or deformation.    At the beginning of the month, I received a call from Fach again. Because of his expansion of the production line, he needed to order 5 green lasers again.  
RFH 35W green laser marking-glass logo, So Easy
RFH 532nm green laser marking glass without deformation
RFH 532nm green laser marking glass without deformation
RFH 532nm green laser marking glass without deformation   South Korean customer Fach produces glass wine cups. Before, the factory also used a brand of green laser, but there were always some wine cups with little defects which were overheated during processing, causing the wine cups to scorch or even deform.   Introduced by a friend, Fach has learned that the RFH Expert III 532 green laser is very effective for marking glass. So he has ordered one from us and tested the effect. After using our laser, Fach said that the heat affected area of the laser during processing is very small, which is very suitable for their laser application, and there will be no scorching or deformation.    At the beginning of the month, I received a call from Fach again. Because of his expansion of the production line, he needed to order 5 green lasers again.  
RFH 532nm green laser marking glass without deformation
Get the latest offers Subscribe for our newsletter

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

Leave A Message
Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

About

contact