-
5W FEMTOSECOND LASER FOR MULTI-PHOTON MICROSCOPY!
May 11 , 2021
THE NEW ALCOR 1064NM 5W FEMTOSECOND LASER FOR MULTI-PHOTON MICROSCOPY! The ALCOR laser series from SPARK Lasers just received a nice power boost! This series, offered in a dual 920nm and 1064nm wavelength configuration up to 2W, or a single wavelength configuration with up to 4W at 920nm (highest power 920nm fs laser on the market), now expands it's offerings to 5W of power at 1064nm! The new ALCO...
view more
-
Nanosecond green laser marking watch glass mirror has anti-counterfeiting effect
May 12 , 2021
Nanosecond green laser marking watch glass mirror has anti-counterfeiting effect Glass is fragile, so engraving on the surface of glass products requires high craftsmanship. The laser marking adopts non-contact processing, which has fast engraving speed, high efficiency, long use time, high engraving accuracy, and fine marking lines. It is especially suitable for engraving LOGO trademarks, ...
view more
-
uv or green laser Etching on Glass
May 12 , 2021
How deep will the laser etch into glass? With a laser you can create a very light etch. This is not sandblasting and you won't achieve that depth, but you can quickly create very elaborate designs with a laser that is lightly etched into the glass. It's a unique look that many people prefer to sandblasting. Do I have to mask the glass before engraving? Unlike sandblasting, wit...
view more
-
Is laser engraving on ABS plastic harmful if you smell it?
May 13 , 2021
Is laser engraving on ABS plastic harmful if you smell it? Did you apply a data-driven approach to improve site structure? A confusing site architecture doesn‘t confuse Google, it impacts profits. Untangle it to see results! Of course no. Check the wikipedia below first: ABS is stable to decomposition under normal use and polymer processing conditions with exposure to carcinoge...
view more
-
What is the cheapest and best place to get plastic, laser engraved?
May 13 , 2021
What is the cheapest and best place to get plastic, laser engraved? The "right" answer to this question is going to depend on exactly what you need done. What you're describing is, for industrial manufacturers of things, still a relatively short run, and laser cutting/engraving is much like printing. The setup is the hard part, and the rest is largely about letting it run. Here are the sorts of qu...
view more
-
How do you laser-engrave a gradient on acrylic
May 13 , 2021
How do you laser-engrave a gradient on acrylic? Should I fill in lighter sections with a pattern (dots) or with a shallower solid fill? Steve Anderson, former Equipment Tech III Specialized Physics & Astronomy at Sonoma State University (1980-2019) Answered 3 years ago · Author has 900 answers and 171.1K answer views This is a tough question, depends on the image and the desired ...
view more
-
0.02mm high-precision UV laser is not easy to cause damage to 3C electronic components
May 14 , 2021
0.02mm high-precision UV laser is not easy to cause damage to 3C electronic components Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other co...
view more
-
Nanosecond solid-state laser solves the marking problem of plastic control panel
May 14 , 2021
Nanosecond solid-state laser solves the marking problem of plastic control panel Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other c...
view more
-
Nanosecond UV laser has little thermal influence, marking electronic components
May 14 , 2021
Nanosecond UV laser has little thermal influence, marking electronic components Recently, I received a consultation from a new customer, Mr. Zhou, "I have encountered some problems when laser marking precision electronic parts of household appliances. For example, the use of laser marking pattern marking on the controller board, because the control board has been pre-installed with other co...
view more
-
Application of picosecond laser cutting machine in circuit board industry
May 14 , 2021
Application of picosecond laser cutting machine in circuit board industry The principle of the picosecond laser cutting machine is to focus the laser light emitted from the laser into a high-power density laser beam. When the laser beam irradiates the surface of the workpiece, the workpiece reaches the melting point or boiling point, and the high-pressure gas coaxial with the beam will melt...
view more
-
For laser marking on plastics, 3W5W UV laser can be selected
May 17 , 2021
For laser marking on plastics, 3W5W UV laser can be selected Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is a function of the wavelength. Therefo...
view more
-
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear
May 17 , 2021
UV laser marking plastics, white\black\graphics and texts can be marked, and the marking is clear Lasers are roughly classified into fiber lasers, carbon dioxide lasers, and ultraviolet lasers. Some plastics are easy to mark because they absorb laser light, while some plastics do not absorb laser light and cannot be marked with laser light at all. The absorption rate of the laser is ...
view more
